Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
What're your thoughts on Tools You Need to Install a New Bathtub ?
Setting up a tub isn't specifically rocket science, however it does need solid plumbing, carpentry, as well as often, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough job. If the old bathtub is conveniently easily accessible, the project can relocate rapidly; if you have to open a wall to remove the old tub and also position the new bath tub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Ensure you have actually qualified on your own for the job as well as are comfortable attempting it. Instead of hiring a contractor to take control of a halfway-completed project, it is far better to think about using one prior to you start. Possibilities are you might require a specialist plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your shower room if you have actually already purchased a brand-new tub and also don't need to transform the arrangement of your previous supply of water pipes.
Your devices and material checklist must comprise the following:
Preparing for the Setup
To start with, the supporting frame provided with the bathroom should be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to prevent strain on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be suited its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite troublesome due to the restricted accessibility that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipelines. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the needed placement. The wood boards are valuable in equally spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four small points.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To set up taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression sign up with; then do the same for the various other faucet.
Switch on the water supply and also inspect all joints and brand-new pipework for leaks and also tighten them if required. Fill the tub and additionally examine the overflow outlet as well as the normal outlet for leakages.
Lastly, repair the bath paneling as defined in the manufacturer's user's manual. Tiling as well as securing around the bathtub must wait until the tub has actually been made use of a minimum of when as this will settle it right into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers remain in location in between the tap as well as the sink. Safeguard the faucet in position with the producer offered backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to pass through the wall between the bath and also the tiling, bring about difficulties with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components and also installations. They are sold in tubes and cartridges, and also can securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealer can break relatively very early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was introduced to that write-up on Installing A Bathtub from an acquaintance on our other website. So long as you liked our page please remember to pass it around. I take joy in reading our article about How to Install a Bathtub.
Just a call away! Report this page